Menvier Security TS700 Manual de Instruções Página 8
- Página / 32
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Installing Remote Keypads and LECs
The following types of devices may be connected to the control panel:
NETLED - 4 x 7 Segment LED display.
NETSTAR - 8 C haracter Starb urst LCD dis play.
NETARM - Remote Arming st ation (Power LED & programmable "Function" LED).
TS700.LEC - 2 zone local expansion card.
Any combination of devices can be used on the same system, providing the total number does
not exceed four.
1. Alwaysensurethatallpower(mainsandbattery)is removed befor e makinganyconnections
to the remote keypad.
2. Separate the cover and base by us ing a screwdriver to push 2 of the clips (top or bottom)
inward from the base indents, then lift the cover a ssembly, noting thatth e PCB is fixed t o the
under side of the cover.
3. Holdthebaseinposition (keyholetothe top)andmarkthethree securingholes, drilla ndplug
the wall as required. Pass all the cables int o the base via th e cable entry points as
appropriate and secure the base to the wall.
4. Connect “Remote Network” and detection circuit cables to the approp riate t ermi nals, see
Figure 4.
5. Set the I/D selector jumper link to the required position:
I/D Selector Circuit A Circuit B Panel Output
1 09 10 5
2 11 12 6
3 13 14 7
4 15 16 8
ENG / NU LL N/A N/A N/A
☞
No two remote keypads or LECs shou ld have the same I/D.
☞
If the I/D is set to “ENG” the remote keypad will function as an Engineer’s keypad
allowing it to be plugged onto the control panel so that system programming and
testing may be carried out (see Engineer’s Keypad).
6. Fordetailson a llremote keypadoption links, please r efer to the instructionssupplied withthe
remote keypad.
7. Finally cliptheremote ke ypad cover ontothe base being carefulnott o trapanycables or to
obstruct the tamper switch.
Engineer's Keypad
Normally a ll system programming will be carried out from one of the installed remote keypads.
However sometimes it may be more convenient to program the system at the control panel, this
can be achieved by using an Engineers Keypad. This is temporarily plugged on to the control
panel (JP2). To convert a standard remote keypad to an "Engineers Keypad" an interface lead
can be obtained from your supplier (P/No. NETEKI).
8
System Ins tallation TS700 Installation Manual
- Instructions 1
- Contents 2
- Overview 3
- Specific ations 4
- System Installation 5
- PCB Layout 6
- Wiring Detection Circuits 7
- Engineer's Keypad 8
- Spare Core 9
- Installing a Plug-on Digicom 10
- Sounder Connections 11
- Installing Output Modules 12
- Connecting a Printer 12
- Programmable O utp uts 13
- Pre Power-Up Checks 14
- Initial Power-Up 14
- Power-Up Checks 14
- Factory Default Parameters 15
- Programming 16
- No Type Function 17
- B or C (see Table 3.) 18
- Table 5a & 5b) 19
- Setting Modes 20
- System Print 21
- Remote Reset Algorithm 21
- System Conf iguration 21
- Circuit 03 is Healthy 22
- Circuit 03 is Active 22
- Time entered 1805 (6:05 pm.) 22
- Change Date 23
- Conf igure Chime Ci rcuits 23
- Conf igure 24 Hour Omit Group 23
- Print System Log 24
- Conf igure Part-Set Groups 24
- View System Log 24
- Reset Master User 1 24
- Appendices 26
- Programming proc edure 27
- Workshop 28
- Installation Record 30
- Quick Reference Guide 31
- Menvier Security Ltd 32
- Kenn Road, Clevedon 32
- Bristol BS21 6LH, England 32
- Tel: +44 (0)1275 870078 32
- Fax: +44 (0)1275 343453 32
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Menvier Security TS700
(10 páginas)Detex 14DN Trim podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Bezpieczeństwo Detex 14DN Trim.
Dostarczamy 1 pdf podręczników Detex 14DN Trim do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentários a estes Manuais