Menvier Security TS700 Especificações descarregar pdf (Página 33)

18 Ward Menu Duration

If the timer is set to 000 the “Code Set Group”

passcodes function as normal, i.e., when the

user enters their passcode the exit timer starts

and the system attempts to set, on entering

their passcode during entry, the wards

assigned to their “Code Set Group” are unset.

If the timer is set to anything other than zero all

“Code Set Group” users are displayed a “Ward

SelectionMenu”.Themenuwillprompttheuser

to select the wards that they require to set and

unset duringthesetting& unsetting procedure.

The user can only select the wards which have

been allocated to their “Code Set Group”,

e.g., If “Code Set Group A” has been defined

by the engineer to set wards B & C, the user

can only affect wards B & C. Note: standard

and master users may also access the “Ward

Selection Menus”, see timer 21. This timer has

a working range of 000-199 seconds.

19 Test Call

If the system is fitted with a plug-on digicom

(DC3, DC3M, DC54, DC58 or DC58M) it is

possible for the control panel to make the

digicom send a timed test call to the central

station. The “Test Call” timer sets the period of

activation, i.e., 000=Disabled, 001=daily,

007=weekly etc. Once programmed the

digicom will send the test call at 3.00 AM. This

timer has a working range of 000-199 days.

20 2nd Alarm Time

This timer controls the duration of the “Second

Alarm” output. This timer has a working range

of 000-199 seconds.

21 Part Set Codes

The value of this counter determines which

standard users are given access to the “Ward

Selection Menu”. For example if the counter is

set to 021, users 21 through to 31 have access

to the menu. If the timer is set to 032 or above,

none of the standard/master users have

accesstothemenu.Thiscounterhasaworking

rangeof000-199.Note:“CodesetGroups”are

not affected.

22 Line Fault Delay

This timer delays the “audible” line fault

indication when a telephone line fault occurs.

The display and any outputs programmed as

“Line Fault” are not affected. This timer has a

working range of 000-199 minutes.

23 Mains Off Delay

This timer delays the “audible” mains off

indication when the mains power is removed.

The display and any outputs programmed as

“Mains Off” are not affected. This timer has a

working range of 000-199 minutes.

24 No Remote Resets

This counter determines how many coded

“Remote Resets” can occur before the system

locks into engineer reset only. Note: Remote

Reset by the RR pins are also affected by this

counter. This counter has a working range of

000-199.

25 Monitor Duration

This timer affects the duration of the “Timed

Output” (No. 070). This timer has a working

range of 000-199 minutes.

26 Activity Duration

This timer sets the duration for which all

“Flagged” circuits must be activated within in

order that the system may be set without

flagging inactive circuits. Once the timer

expires it is restarted and all “Flagged’ circuits

must once again be re-activated. This timer

has a working range of 000-199 hours.

27 Part Set Entry Time

This timer sets the entry period for the system

when the system is in the part-set condition. If

the timer is set to 000 the part-set entry timer is

thesameasthemain entrytimer(timer05).This

timerhasaworkingrangeof000-199seconds.

28 Abort Delay

This timer sets the period in which the alarm

signal may be aborted following an alarm

condition. When an alarm occurs, the “Abort

Output” (071) is only activated if the system is

unset within this period. If the system is unset

after this period the abort output is NOT

activated. This timer has a working range of

000-199 seconds.

TS900 Installation Manual Engineer's Menu 1

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 67 68

Comentários a estes Manuais

Sem comentários

Menvier Security TS700 Especificações Página 33

Comentários a estes Manuais