Menvier Security TS900+ Especificações Página 17
- Página / 68
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
End Of Line
The EOL method requires the following:
l
The detector alarm contacts must have a 4K7
shunt resistor fitted.
l
A 2K2 End of Line (EOL) resistor must be fitted at
the point in the circuit furthest from the control
panel.
l
Loop resistance with the EOL resistor shorted
must be less than 100 Ohms.
l
The maximum number of detection
devices allowed in a circuit is ten.
l
Normally open devices such as pressure
pads and exit terminator buttons are
connected across outer terminals
l
If the detection circuit is not used links can
be fitted across the zone and tamper
loops or programmed as Not Used.
External Sounder Connections
The following terminals have been provided to
allow connections to an external sounder:
H/O - This is used to provide a permanent -ve
hold off to external sounders, strobes etc.
H/O + This is used to provide a permanent +ve
hold off to external sounders, strobes etc.
It is protected by a 1 Amp fuse (Bell 12V).
TR - This is the negative tamper return
connection from the siren or bell.
STB - This is the strobe output which will switch to
0V on alarm and is rated at 500mA.
Connect the other side of the strobe to
the H/O +.
TRG - This is the bell trigger output which will
switch to 0V on alarm and is rated at
500mA. This output can be programmed
for SAB or SCB operation, as follows:
SAB: TRG - will switch to 0V on alarm and
will provide a maximum of 500mA.
SCB: TRG - will provide a negative hold
off (500mA), which is removed on alarm.
13
TS790 & TS900 Installation Manual System Installation
Alarm
Tamper
CIRCUIT A
ZA
TA
CIRCUIT A
ZA
TA
CIRCUIT A
ZA
TA
Alarm
Tamper
Max. 10 devices per circuit
Wiring N.O. devices (Exit Terminators)
Alarm
Tamper
500 meters or 100 Ohms
Figure 13. Double Pole Wiring
500 meters or 100 Ohms
Alarm
Alarm
Tamper
Max. 10 devices per circuit
Wiring N.O. devices (Exit Terminators)
Tamper
4K7 = Yellow, Violet, Red
2K2 = Red, Red, Red
Alarm
Tamper
4K7
4K7
4K7
2K2
2K2
2K2
CIRCUIT B
ZB
TB
CIRCUIT B
ZB
TB
CIRCUIT B
ZB
TB
Figure 14. End of Line Wiring
- TS790 & TS900 1
- Overview 3
- System Installation 3
- Engineer’s Menu 1 3
- Engineer's Menu 2 3
- Engineers Menu 3 4
- Appendices 4
- System Architecture 5
- Control Panel 5
- Remote Keypads 6
- TS900 NODE 6
- ID Node (TS900.IDNODE) 6
- TS700 LEC 6
- Specifications 6
- Cable Routing 7
- Remote Network Wiring 8
- Control Panel Installation 9
- Control Panel PCB Layout 10
- NETLCD Remote Keypad 12
- NETSTAR Remote Keypad 12
- NETLED Remote Keypad 12
- NETARM Remote Arming Station 12
- PCB Layouts & Connections 12
- Tamper Switch 13
- ENT Key Disable 13
- Engineer’s Keypad 14
- Figure 11. TS900 Node Layout 15
- TS700 LEC Installation 16
- Wiring Detection Circuits 16
- External Sounder Connections 17
- Auxiliary Tamper 18
- Extension Loudspeakers 18
- Digicom/RedCARE Installation 19
- Plug-on Digicom Installation 19
- Connecting a Printer 20
- Programmable Outputs 21
- Pre Power-Up Checks 22
- Initial Power-Up 22
- Power-Up Checks 23
- NVM Defaults 23
- Introduction 25
- Panel Outputs 26
- Digicom Outputs 26
- Digicom Channels 26
- Programmable Output Types 26
- Program Circuits 29
- Circuit Attributes 30
- System Timers 31
- Setting Modes 34
- Do System Print 34
- Remote Reset Algorithm 35
- Configuration 35
- Goto User Menu 1 37
- View Location Text (LCD Only) 38
- Relearn Hardware 38
- View Circuits 40
- Set System Time 40
- Set System Date 40
- Change Passcode 40
- Chime Circuits 41
- Alter 24Hr Group 41
- Print System Log 41
- Configure Wards 41
- Log Event Codes 42
- View System Log 42
- StarburstLCD 44
- Menu Contents 45
- Time Switches Flowchart 46
- Part Set Group Operation 47
- Code Set Group Operation 47
- Reset Message 48
- Banner Message 48
- Location Text 49
- Printer Header 49
- Part Set Banner 49
- Current Consumption 49
- View Inactive Circuits 50
- Custom Outputs A & B 51
- Modem Options (LCD Only) 52
- Program Digi Flowchart 53
- Reset Digicom 54
- Point ID Extended Reporting 55
- Workshop Canteen 59
- Service Department 59
- Key Point Application Example 60
- Text Editing Keys 62
- Setup New Users 63
- Setup New Users Flowchart 64
- 496487 Issue 3 68
Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Menvier Security TS900+
Sistemas de segurança - controlo de acesso Menvier Security TS2500 Manual do Utilizador
(60 páginas)
(60 páginas)
Sistemas de segurança - controlo de acesso Menvier Security TS2500 Manual do Utilizador
(48 páginas)
(48 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais